How Latency Works
- Live Versions: All
- Operating System: All
Note: The following article is purely informational. For more specific troubleshooting advice, please refer to our article on How to reduce latency.
- What is Latency?
- Where Latency Occurs
- Use Cases
- How Live adapts to latency
- Preparing your system for sample-accurate recording
- Further Reading
What is Latency?
Latency refers to a short period of delay between when a signal enters a system, and when it emerges from it. In a Digital Audio Workstation, some amount of latency is always necessary to allow audio data to be captured by your audio interface, passed to your DAW (or other application), processed by instruments/effects within the DAW, and then passed back out to the output of the audio interface.
Latency cannot be avoided, but it can be understood!
What Causes Latency?
In digital audio, latency is introduced by signal conversion and audio buffers within the signal path.
An Analog-to-Digital (AD) signal converter transforms incoming audio into data that can be processed by the computer. Conversely, Digital-to-Analog (DA) Converters transform data into an analog audio signal that is sent to the speakers or audio effects. In most studios, this task is handled by an audio interface.
An audio buffer is a region of physical memory storage used to temporarily store chunks of data as the signal travels from one location to the next. (Larger buffer sizes take longer to process, which increases the overall latency).
Where Latency Occurs
- The audio interface
- The audio interface driver
- The operating system
- Between the Audio Interface and the DAW
- In the DAW’s signal processing (eg. monitored tracks / native effects / plug-ins / etc.)
Settings in Live that affect latency
Reduced Latency When Monitoring
As mentioned, audio is processed in chunks of individual samples. Processing in larger chunks can result in audible latency, whereas smaller chunks generally create a lower global latency value. However, smaller chunks of samples are loaded/unloaded at a much faster rate in order to maintain consistent playback, which creates a higher CPU load on the system. If the CPU is unable to keep up, the missing chunks can be heard as crackles or dropouts.
In digital recording, audio is represented by a series of data points called “samples”. These samples are strung together in rapid succession by the computer, this results in an audible waveform. The audio sample rate determines the frequency at which these samples are recorded, generated, and output by the system. (Higher sample rates will result in a slightly lower global latency, but create more demand on the CPU).
Because signals cannot be processed before they ever happen, negative delay values do not actually move the track’s signal ahead in time. In reality, every other track within the session is delayed by that amount in order to achieve the same effect.
The output of any track can be delayed or pre-delaying in milliseconds in order to compensate for human, acoustic, hardware and other real-world delays (or for creative purposes). However, the amount of delay applied to a track’s output will be interpreted as latency when the signal is monitored in real-time.
Graphics are not latency-compensated in Live, in order to reserve computing resources for the audio stream. This can sometimes result in a noticeable lag in Live’s graphics in Live Sets with an extreme amount of internal latency, but is imperceptible in most other cases.
Editing in Max for Live
Max for Live devices will introduce additional latency when their editor window is open. (More info here).
Device settings that affect latency
Note: With the exception of the first topic, the points below apply to both Live’s native devices and compatible third party plug-ins.
Plug-In Delay Compensation
If the CPU load of a plug-in is low enough for the processor to calculate all of its functions within a single audio buffer, it will not create any additional latency. If not, the plug-in will report the time discrepancy to the DAW, which delays the output of the entire signal path by the same amount to maintain consistent playback.
Some plug-ins can cause a significant amount of latency due to the amount of processing required for high-quality output. This can create some frustration when monitoring signals in larger sessions, since a few high-CPU devices can create significant delays for the entire session.
External Instrument & External Audio Effect
As these devices send and/or receive audio from outside Live, they will delay the audio by the Overall Latency amount in preferences. In addition, when setting the 'Hardware Latency' slider to any amount other than zero, this will increase the global latency.
Some devices include a "lookahead" feature, which applies a slight delay on the incoming signals. (eg. - Live’s Compressor uses Lookahead to apply dynamic changes that would be impossible to create in real-time).
In order to convert a signal from the time domain to the frequency domain for the purposes of processing or display, a fairly large buffer of audio is needed. As a result, devices that do any kind of spectral processing will likely create some amount of latency.
Other advanced processing options (Oversampling / Convolution / etc.)
Some devices require especially large sample buffers in order to make intelligent decisions about how to behave not just based on a single instant in time (one sample) but based on a period of time (a larger block of samples). This is especially true for mastering plugins such as iZotope’s Ozone, which introduces a significant (but necessary!) amount of latency in order to perform all of its operations.
Other factors that affect latency
Inefficient/outdated audio interface drivers
On Windows machines, ASIO drivers generally perform better than MME/DirectX.
Also, outdated drivers can slow things down due to influence from outside factors, such as operating system updates or changes made to the DAW. Manufacturers often release firmware updates for their products to compensate for these changes, or to simply refine the device’s performance.
Deactivated Instruments & Effects
The yellow button in the top-left corner of all instruments and effects is used to deactivate the device. Since this parameter can be freely automated/modulated by the user, eliminating the device’s latency every time the button is toggled would create noticeable distortions to the output. To prevent this, device latency is always in effect, even when it is disabled.
Understanding latency can be difficult, since the symptoms are often very different from their root cause. Below are a few examples that illustrate this.
Note - The latency times shown below are simplified for demonstration purposes; Results may vary in real life.
Scenario 1 - MIDI Latency
In this scenario, the user experiences a latency between pressing a note on their MIDI controller and hearing the resulting audio output.
- It takes 1 ms for the signal to go from the keyboard output to the computer’s input.
- Once the MIDI signal is in the computer, it takes 1 ms for it to be processed internally by the DAW (which converts it into audio).
- The resulting audio signal then takes 1 ms to travel out of the DAW, back to the audio interface, and to the speakers.
Since the signal travels in a linear path, there is no way for each part of the process to occur simultaneously, and the user experiences an overall latency of 3 milliseconds.
Scenario 2 - Audio Latency
In this scenario, the user experiences a latency between speaking into a microphone and hearing the resulting audio output.
- It takes 0 ms for the signal to go from the microphone to the input of the audio interface (since analog signals are almost instantaneous).
- The audio interface then takes 1 ms to convert the signal into a digital format, and pass it to the computer.
- Once inside the computer, the signal takes 1 ms for it to be processed internally by the DAW.
- The resulting audio signal then takes 1 ms to travel out of the DAW, through the computer, to the audio interface, and (finally) to the speakers.
Since the signal is traveling in a linear path, there is no way for each part of the process to occur simultaneously, and the user experiences an overall latency of 3 milliseconds.
How Live adapts to latency
Live establishes the amount of latency caused by each individual component within the system in order to track the global latency value for the session.
When Delay Compensation is enabled, this value is determined by whichever signal path causes the highest amount of latency, so that Live can delay the output of each signal path by the necessary amount of time to match it. As a result, the audio played through the Master track is identical to that of a latency-free configuration. (With Delay Compensation disabled, however, the global latency value is ignored and each point of monitoring contains an amount of latency that is unique to the signal path behind it).
Take, for example, the following Live Set with two tracks...
“Audio Track 1” contains several devices that create an overall latency of 120ms, and “MIDI Track 1” has a latency of 80ms. With Delay Compensation active, both tracks are delayed by a total of 120ms, so that even the track with the highest amount of latency is able to keep up with the rate of playback.
However, "MIDI Track 1" contains a software instrument. In order to play it, you need to set the monitor to In or Auto and arm the track for recording. Since the track is being delayed by 120ms (so that it plays in time with the rest of the tracks), it's going to feel quite sluggish when playing it.
With Reduced Latency When Monitoring enabled, however, the overall latency of the set is bypassed for monitored tracks. So when Track 2 is monitored, it will only contain the 80ms of latency caused by the devices directly within its signal path. This can be helpful in situations where the user wants to record new material into an otherwise latency-heavy session but still wants the rest of the tracks to play with Delay Compensation enabled.
Preparing your system for sample-accurate recording
When recording a new audio track into Live, it can often help to set the track’s monitor setting to “Off”, and monitor the instrument signal directly while recording (bypassing Live).
This presents a challenge, however, since the resulting recording would sound slightly off-time due to the latency added by the system at the time of recording. To adjust for this timing discrepancy, Live automatically offsets the recording by whatever amount of latency is reported from the audio interface. Ideally, this results in a recording that is perfectly in-time with the signal that the performer listened to during recording.
However, some interfaces report this latency value inaccurately, and Driver Error Compensation allows Live to adjust for these incorrect values. Live has a built-in lesson including a specifically calibrated set that allows you to set DEC. For the lesson, you will need a cable and an audio interface with at least one physical input and output. This can be found in the help view. (Help → Help View → Audio I/O → Page 8 of the Lesson, click the link for Driver Error Compensation).
Note: While Driver Error Compensation will have an effect on the latency of your recordings, it is not meant to reduce real-time latency.